Здравствуйте.
Проблема такая. Поставили в сети на 2 машинах prman 11.5.3 . на каждой отдельной машине всё здорово, рендерит замечательно, лицензию настроили. Попытка поднять сетевой рендер не увенчалась успехом
сам alfserver поднят на каждой машине (проверяли телнетом на его порт - пишет версию сервера, всё ок.) а вот запуск команды netrender -h 192.168.0.124 test.rib очень надолго задумывается и висит на 0%. Причем пытались опциями включить логи (включили всё, что только можно), выдает что-то такое:
listen for reply on port: 1575
From: wpavel
Render on host: 192.168.0.124 192.168.0.45 (as 192.168.0.45)
Request replied, ok for 1 processors
Accepting reply ...
connection from host: DEG
, addr: 192.168.0.124
Accepted i/o connections from 192.168.0.124
error stream on pid <1792>
Request packet from 548:
cmd: 10 : ID seq: 1 fileindex: 0 flags: 0x0 offset: 0 bytes: 0
Reply packet to 548:
cmd: 10 : ID seq: 1 fileindex: 4 status: 0 bytes: 0
Request packet from 548:
cmd: 1 : OPEN seq: 2 fileindex: -1 flags: 0x101 offset: 438 bytes: 19
Attempt to open: defaultsurface.slo
Reply packet to 548:
cmd: 1 : OPEN seq: 2 fileindex: 4 status: 0 bytes: 0
Request packet from 548:
cmd: 3 : READ seq: 3 fileindex: 4 flags: 0x2 offset: 0 bytes: 4096
sending 869 bytes of read data
Reply packet to 548:
cmd: 3 : READ seq: 3 fileindex: 4 status: 0 bytes: 869
Request packet from 548:
cmd: 2 : CLOSE seq: 4 fileindex: 4 flags: 0x0 offset: 0 bytes: 0
Reply packet to 548:
cmd: 2 : CLOSE seq: 4 fileindex: 0 status: 0 bytes: 0
Request packet from 548:
cmd: 1 : OPEN seq: 5 fileindex: -1 flags: 0x101 offset: 438 bytes: 17
Attempt to open: distantlight.slo
Reply packet to 548:
cmd: 1 : OPEN seq: 5 fileindex: 4 status: 0 bytes: 0
Request packet from 548:
cmd: 3 : READ seq: 6 fileindex: 4 flags: 0x2 offset: 0 bytes: 4096
sending 684 bytes of read data
Reply packet to 548:
cmd: 3 : READ seq: 6 fileindex: 4 status: 0 bytes: 684
Request packet from 548:
cmd: 2 : CLOSE seq: 7 fileindex: 4 flags: 0x0 offset: 0 bytes: 0
Reply packet to 548:
cmd: 2 : CLOSE seq: 7 fileindex: 0 status: 0 bytes: 0
Request packet from 548:
cmd: 1 : OPEN seq: 8 fileindex: -1 flags: 0x101 offset: 438 bytes: 17
Attempt to open: ambientlight.slo
Reply packet to 548:
cmd: 1 : OPEN seq: 8 fileindex: 4 status: 0 bytes: 0
Request packet from 548:
cmd: 3 : READ seq: 9 fileindex: 4 flags: 0x2 offset: 0 bytes: 4096
sending 431 bytes of read data
Reply packet to 548:
cmd: 3 : READ seq: 9 fileindex: 4 status: 0 bytes: 431
Request packet from 548:
cmd: 2 : CLOSE seq: 10 fileindex: 4 flags: 0x0 offset: 0 bytes: 0
Reply packet to 548:
cmd: 2 : CLOSE seq: 10 fileindex: 0 status: 0 bytes: 0
Request packet from 548:
cmd: 1 : OPEN seq: 11 fileindex: -1 flags: 0x101 offset: 438 bytes: 12
Attempt to open: plastic.slo
Reply packet to 548:
cmd: 1 : OPEN seq: 11 fileindex: 4 status: 0 bytes: 0
Request packet from 548:
cmd: 3 : READ seq: 12 fileindex: 4 flags: 0x2 offset: 0 bytes: 4096
sending 1265 bytes of read data
Reply packet to 548:
cmd: 3 : READ seq: 12 fileindex: 4 status: 0 bytes: 1265
Request packet from 548:
cmd: 2 : CLOSE seq: 13 fileindex: 4 flags: 0x0 offset: 0 bytes: 0
Reply packet to 548:
cmd: 2 : CLOSE seq: 13 fileindex: 0 status: 0 bytes: 0
Request packet from 548:
cmd: 5 : ERROR seq: 14 fileindex: 0 flags: 0x0 offset: 0 bytes: 14
0%
и всё. и на этом висит. причем наоборот тоже эти серваки не хотят рендерить. Естественно из Майки тоже ничего не получается. Когда ставишь там нетрендер, то альфред говорит что сервер занят (что-то такое).
Если кто-нибудь что-нибудь подскажет - спасибо.
Проблема такая. Поставили в сети на 2 машинах prman 11.5.3 . на каждой отдельной машине всё здорово, рендерит замечательно, лицензию настроили. Попытка поднять сетевой рендер не увенчалась успехом
сам alfserver поднят на каждой машине (проверяли телнетом на его порт - пишет версию сервера, всё ок.) а вот запуск команды netrender -h 192.168.0.124 test.rib очень надолго задумывается и висит на 0%. Причем пытались опциями включить логи (включили всё, что только можно), выдает что-то такое:
listen for reply on port: 1575
From: wpavel
Render on host: 192.168.0.124 192.168.0.45 (as 192.168.0.45)
Request replied, ok for 1 processors
Accepting reply ...
connection from host: DEG
, addr: 192.168.0.124
Accepted i/o connections from 192.168.0.124
error stream on pid <1792>
Request packet from 548:
cmd: 10 : ID seq: 1 fileindex: 0 flags: 0x0 offset: 0 bytes: 0
Reply packet to 548:
cmd: 10 : ID seq: 1 fileindex: 4 status: 0 bytes: 0
Request packet from 548:
cmd: 1 : OPEN seq: 2 fileindex: -1 flags: 0x101 offset: 438 bytes: 19
Attempt to open: defaultsurface.slo
Reply packet to 548:
cmd: 1 : OPEN seq: 2 fileindex: 4 status: 0 bytes: 0
Request packet from 548:
cmd: 3 : READ seq: 3 fileindex: 4 flags: 0x2 offset: 0 bytes: 4096
sending 869 bytes of read data
Reply packet to 548:
cmd: 3 : READ seq: 3 fileindex: 4 status: 0 bytes: 869
Request packet from 548:
cmd: 2 : CLOSE seq: 4 fileindex: 4 flags: 0x0 offset: 0 bytes: 0
Reply packet to 548:
cmd: 2 : CLOSE seq: 4 fileindex: 0 status: 0 bytes: 0
Request packet from 548:
cmd: 1 : OPEN seq: 5 fileindex: -1 flags: 0x101 offset: 438 bytes: 17
Attempt to open: distantlight.slo
Reply packet to 548:
cmd: 1 : OPEN seq: 5 fileindex: 4 status: 0 bytes: 0
Request packet from 548:
cmd: 3 : READ seq: 6 fileindex: 4 flags: 0x2 offset: 0 bytes: 4096
sending 684 bytes of read data
Reply packet to 548:
cmd: 3 : READ seq: 6 fileindex: 4 status: 0 bytes: 684
Request packet from 548:
cmd: 2 : CLOSE seq: 7 fileindex: 4 flags: 0x0 offset: 0 bytes: 0
Reply packet to 548:
cmd: 2 : CLOSE seq: 7 fileindex: 0 status: 0 bytes: 0
Request packet from 548:
cmd: 1 : OPEN seq: 8 fileindex: -1 flags: 0x101 offset: 438 bytes: 17
Attempt to open: ambientlight.slo
Reply packet to 548:
cmd: 1 : OPEN seq: 8 fileindex: 4 status: 0 bytes: 0
Request packet from 548:
cmd: 3 : READ seq: 9 fileindex: 4 flags: 0x2 offset: 0 bytes: 4096
sending 431 bytes of read data
Reply packet to 548:
cmd: 3 : READ seq: 9 fileindex: 4 status: 0 bytes: 431
Request packet from 548:
cmd: 2 : CLOSE seq: 10 fileindex: 4 flags: 0x0 offset: 0 bytes: 0
Reply packet to 548:
cmd: 2 : CLOSE seq: 10 fileindex: 0 status: 0 bytes: 0
Request packet from 548:
cmd: 1 : OPEN seq: 11 fileindex: -1 flags: 0x101 offset: 438 bytes: 12
Attempt to open: plastic.slo
Reply packet to 548:
cmd: 1 : OPEN seq: 11 fileindex: 4 status: 0 bytes: 0
Request packet from 548:
cmd: 3 : READ seq: 12 fileindex: 4 flags: 0x2 offset: 0 bytes: 4096
sending 1265 bytes of read data
Reply packet to 548:
cmd: 3 : READ seq: 12 fileindex: 4 status: 0 bytes: 1265
Request packet from 548:
cmd: 2 : CLOSE seq: 13 fileindex: 4 flags: 0x0 offset: 0 bytes: 0
Reply packet to 548:
cmd: 2 : CLOSE seq: 13 fileindex: 0 status: 0 bytes: 0
Request packet from 548:
cmd: 5 : ERROR seq: 14 fileindex: 0 flags: 0x0 offset: 0 bytes: 14
0%
и всё. и на этом висит. причем наоборот тоже эти серваки не хотят рендерить. Естественно из Майки тоже ничего не получается. Когда ставишь там нетрендер, то альфред говорит что сервер занят (что-то такое).
Если кто-нибудь что-нибудь подскажет - спасибо.